The house has underfloor heating on the ground floor and traditional radiators upstairs, each supplied by a separate pump. The boiler operates correctly, but upstairs stubbornly stays cold, the system is noisy, and the unit switches on and off at unnaturally short intervals. The culprit is often something rarely discussed directly: the lack of a hydraulic separator, a component that separates circuits with different characteristics so they can operate independently of one another.
The problem of pump conflict in the boiler room
When a single heat source supplies two circuits with completely different characteristics at the same time, such as an extensive underfloor heating system and traditional radiators, each has a different water flow requirement and other hydraulic resistance. Underfloor heating consists of a dense network of long loops, so its pump needs to be powerful enough to push water through the resistance. Radiators offer much less resistance, so their pump can be significantly weaker. If both pumps are connected directly to the same main pipe, without any separation, the stronger pump starts to dominate: it draws more water than it should, at the expense of the weaker one. This creates what installers call pump conflict. The upstairs rooms get cold, the pipes start making noise, and the boiler, trying to keep up with fluctuations in demand, starts switching on and off more frequently.
What is a hydraulic separator and how does it work?
A hydraulic separator is a short section of pipe with a much larger diameter than the rest of the system, installed where the heat source circuit meets the secondary circuits. You can think of it as a traffic-free intersection for two streams of water that would otherwise collide and disrupt each other's flow. Water flowing from a narrow pipe into the much wider body of the separator slows down sharply, because the same amount of water is now spread over a much larger cross-section. According to an independently confirmed rule, the separator body should have a diameter two to three times larger than the connecting pipes, reducing the flow velocity inside to 0.1 to 0.2 meters per second, which is very slow compared with the velocity in ordinary system pipes.
At such a low flow rate, the heat pump's pump and the pumps for the individual circuits stop directly affecting one another. The boiler pump serves only the section up to the hydraulic separator, while each secondary pump draws exactly as much water from it as it currently needs, without disrupting the operation of the others. The system stabilizes itself, without the need to manually balance flow rates between circuits.
What exactly is it used for?
A low-loss header serves two distinct purposes in an installation. The first is the hydraulic separation described above, which protects circuits with different characteristics from interfering with one another. The second comes into play when the flow from the heat source temporarily exceeds the flow required by the consumers, for example when the thermostatic radiator valves close. The excess hot water that the consumers cannot accept at that moment is not forced into the throttled system, but instead flows freely down inside the low-loss header and mixes with the water returning to the boiler. W As a result, the return temperature to the heat source rises, which helps keep it above the threshold at which low-temperature corrosion begins in solid-fuel boilers.
One caveat is worth mentioning right away: the same mechanism works against modern condensing gas boilers. These boilers achieve their high efficiency precisely through a low return temperature, so a low-loss header that is poorly matched to this type of heat source and raises the return temperature excessively can reduce condensing efficiency instead of helping the system.
Low-loss header, buffer tank or mixing valve: three different tools
This is one of the most common sources of confusion in the boiler room: three components that might seem to do similar things at first glance, but in practice serve completely different purposes and cannot always replace one another.
Low-loss header: a pressure separator with no thermal memory
A low-loss header separates hydraulic circuits and acts immediately, but does not store any energy. Its water capacity is usually only a few liters. It is an inexpensive, compact solution that is sufficient when all you need is to separate flows.
Buffer tank: energy storage that also provides separation
A buffer is a much larger tank, ranging from one hundred to as much as a thousand liters, whose main purpose is to store thermal energy rather than simply provide separation. Thanks to its large water capacity, it acts as the thermal inertia of the entire system, helping maintain thermal comfort long after the heat source has stopped running. Connected in parallel with four ports, it also provides hydraulic separation, making a separate low-loss header unnecessary in this configuration. The trade-off for this versatility is a much higher cost and the need for more space in the boiler room, which may not be worthwhile for smaller, simpler upgrades.
Mixing valve: regulates temperature, not flow volume
A mixing valve, either three-way or four-way, does something completely different from the two components above: it changes the water temperature by proportionally mixing the hot flow with cooler water, rather than separating pressures between circuits. W a well-designed, extensive boiler room, both mechanisms often work together: the hydraulic separator stabilizes pressures right at the boiler outlet, and then a mixing valve is installed downstream on a selected circuit, such as underfloor heating, to provide it with a suitably lower temperature.
When a hydraulic separator is unnecessary and when it is essential
If a home has one heat source with its own built-in pump and just one heating circuit with constant resistance, for example, radiators alone without underfloor heating, an additional hydraulic separator is simply an unnecessary expense and another potential point of failure.
A hydraulic separator is warranted when the system is divided into more than one heating circuit with clearly different flow characteristics, especially if each has its own independent pump. A classic example is the combination of underfloor heating and radiators, multi-zone systems in larger homes, and cascade boiler rooms connecting several heat sources at once.
IBO solutions for hydraulic separation
Our range includes the vertical IBO SP-S hydraulic separator, for outputs up to 50 kW, factory-equipped with an automatic air vent at the top of the body and a drain and sludge valve at the base. As well as separating pressure, it helps remove air and fine contaminants from the system, which have time to settle freely at the bottom at such a low flow rate. The body is factory-insulated to limit heat loss, while the built-in thermometer and pressure gauge let you check in real time whether the separation is working as designed.
Dambat – a trusted manufacturer of pumps and hydrotechnical equipment with quality certifications.
Frequently asked questions
What is a hydraulic separator and what is it used for?
It is a short section of pipe with an enlarged diameter, installed between the heat source circuit and the circuits serving the heating system. Its purpose is to hydraulically separate these circuits so that pumps with different capacities do not interfere with each other's operation.
Does a hydraulic separator raise the supply temperature?
No, this is physically impossible because a hydraulic separator has no heat source of its own. At most, it can lower the supply temperature when flow from the heat source is insufficient, or raise the return temperature when there is excess flow.
Can a hydraulic separator be replaced with something else?
Yes, a hydraulic separator can be replaced with a buffer tank. Connected in parallel in a four-port configuration, the buffer tank provides hydraulic separation, making a separate hydraulic separator unnecessary. However, a buffer tank costs more and requires more space than a separator alone.
How does a hydraulic separator differ from a mixing valve?
A hydraulic separator separates pressure and flow between circuits, but does not change the water temperature. A mixing valve does the opposite: it regulates the temperature by proportionally mixing the flows, but does not hydraulically separate the circuits. With a complex boiler room, both components often work together.
Does my system need a hydraulic separator?
When a home has one heat source with its own pump and just one heating circuit with a constant resistance, an additional hydraulic separator is an unnecessary expense.
Why does the underfloor heating pump draw water intended for the radiators?
This happens when both circuits are connected directly to a shared manifold without separation. The stronger pump, usually serving a high-resistance system such as extensive underfloor heating, draws more water than its share, at the expense of the weaker radiator pump. A hydraulic separator solves this by separating the two circuits.






