Description
WATER-PASS 2 controller – smart pump controller with a 1 L tank, IPRO
WATER-PASS 2 is an electronic pump controller from the IPRO brand that automatically switches the pump on and off based on water pressure and flow in the pipeline. WUnlike the WATER-PASS model, it is equipped with a 1 L tank that reduces water hammer, and its switch-on pressure is factory-set to 1.5 bar.
Who it's for
- Installers and well drillers – adjustable switch-on pressure allows a conventional pressure switch to be replaced with a single device, simplifying system installation.
- Users of domestic water systems – the built-in 1 L tank dampens water hammer, reducing noise and stress on the system when the pump switches on.
- Farms and horticulture – controlling pump operation when sprinklers are opened automates irrigation without manually switching on the device.
- Service companies – the built-in dry-run protection safeguards the pump from running without water and reduces the risk of damage.
Applications
- Automatic pump control in domestic water systems with their own water source.
- Maintaining constant pressure in pressurized water supply systems.
- Switching on an irrigation pump when garden sprinklers are opened.
- Replacing a conventional pressure switch in a system exposed to water hammer.
Install the WATER-PASS 2 controller vertically on the pump's discharge side, between the pump and the first water outlet, following the flow direction marked on the housing.
WATER-PASS 2 controller features – description and technical specifications
WATER-PASS 2 controls the pump by detecting changes in water pressure and flow in the pipeline. W practice, it switches the pump on when a tap is turned on or sprinklers are opened, and switches it off about 6 seconds after the water flow is shut off. The built-in 1 L tank reduces water hammer, so no additional diaphragm tank is installed with this model. The built-in check valve prevents water from flowing back into the pump.
If there is no water, the controller switches off the pump, protecting it from running dry. It restarts after the power supply is disconnected and reconnected. The circuit board is protected with epoxy resin, increasing the electronics' resistance to moisture. The device is designed for use with clean water free of mechanical contaminants.
- Supply voltage: 100–260 V
- Frequency: 50/60 Hz
- Maximum controlled pump power: 2.2 kW
- Max. current draw of the controlled pump: 12 A
- Max. operating pressure: 15 bar
- Switch-on pressure range: 0–10 bar
- Switch-on pressure (factory setting): 1.5 bar
- Tank capacity: 1 L
- Max. ambient temperature: 40 °C
- Max. liquid temperature: 80 °C
- Protection rating: IP65
- Operating position: vertical
IPRO - 36-month (3-year) manufacturer's warranty. Warranty and post-warranty service is provided by Dambat.
Dambat - a trusted manufacturer of pumps and hydrotechnical equipment with quality certifications.
Frequently asked questions (FAQ) - WATER-PASS 2 controller
What is the WATER-PASS 2 controller for?
The WATER-PASS 2 is an electronic pump controller from IPRO that automatically switches the pump on when water is drawn and switches it off when water use stops. It maintains constant pressure in the installation and protects the pump from running dry.
What is the 1 L tank in the WATER-PASS 2 for?
The 1 L tank reduces water hammer when the pump switches on and off. For this reason, an additional diaphragm tank is not installed with the WATER-PASS 2.
Does the WATER-PASS 2 protect the pump from running dry?
Yes. When there is no water, the controller switches off the pump after 8 seconds, protecting it from running dry. To restart it, disconnect and reconnect the power supply.
What kind of water can the WATER-PASS 2 work with?
The controller is designed to work with clean water that contains no mechanical impurities. Sand or iron particles may damage the device.
What is the factory-set switch-on pressure of the WATER-PASS 2?
The switch-on pressure on the WATER-PASS 2 is factory-set to 1.5 bar. The switch-on pressure can be adjusted from 0 to 10 bar, allowing you to tailor its operation to your installation.
How is the WATER-PASS 2 different from the WATER-PASS?
The WATER-PASS 2 has a 1 L tank that reduces water hammer, so it does not require an additional diaphragm tank. It also comes with a factory-set switch-on pressure of 1.5 bar. The other parameters and operating principle are the same as those of the WATER-PASS model.
Where can I buy the WATER-PASS 2 controller?
The manufacturer does not sell directly to customers. The WATER-PASS 2 controller is available from retail partners, plumbing wholesalers, and authorized online distributors.
What warranty does the WATER-PASS 2 come with?
The IPRO WATER-PASS 2 controller comes with a 36-month (3-year) manufacturer's warranty. Warranty and post-warranty service is provided by Dambat.
- Power [kW]: 2.2
- Power supply [V]: 1~230 V
- Frequency [Hz]: 50
- Current [A]: 12.0
- Protection rating: IP65
- Dimensions H/W/L [mm]: 200/140/180
- Height (mm): 200
- Width (mm): 140
- Length (mm): 180
- Max. liquid temperature: 80
- Product weight [kg]: 1.0
- Number of pumps supported: 1
WATER-PASS 2 controller – smart pump controller with a 1 L tank, IPRO
WATER-PASS 2 is an electronic pump controller from the IPRO brand that automatically switches the pump on and off based on water pressure and flow in the pipeline. WUnlike the WATER-PASS model, it is equipped with a 1 L tank that reduces water hammer, and its switch-on pressure is factory-set to 1.5 bar.
Who it's for
- Installers and well drillers – adjustable switch-on pressure allows a conventional pressure switch to be replaced with a single device, simplifying system installation.
- Users of domestic water systems – the built-in 1 L tank dampens water hammer, reducing noise and stress on the system when the pump switches on.
- Farms and horticulture – controlling pump operation when sprinklers are opened automates irrigation without manually switching on the device.
- Service companies – the built-in dry-run protection safeguards the pump from running without water and reduces the risk of damage.
Applications
- Automatic pump control in domestic water systems with their own water source.
- Maintaining constant pressure in pressurized water supply systems.
- Switching on an irrigation pump when garden sprinklers are opened.
- Replacing a conventional pressure switch in a system exposed to water hammer.
Install the WATER-PASS 2 controller vertically on the pump's discharge side, between the pump and the first water outlet, following the flow direction marked on the housing.
WATER-PASS 2 controller features – description and technical specifications
WATER-PASS 2 controls the pump by detecting changes in water pressure and flow in the pipeline. W practice, it switches the pump on when a tap is turned on or sprinklers are opened, and switches it off about 6 seconds after the water flow is shut off. The built-in 1 L tank reduces water hammer, so no additional diaphragm tank is installed with this model. The built-in check valve prevents water from flowing back into the pump.
If there is no water, the controller switches off the pump, protecting it from running dry. It restarts after the power supply is disconnected and reconnected. The circuit board is protected with epoxy resin, increasing the electronics' resistance to moisture. The device is designed for use with clean water free of mechanical contaminants.
- Supply voltage: 100–260 V
- Frequency: 50/60 Hz
- Maximum controlled pump power: 2.2 kW
- Max. current draw of the controlled pump: 12 A
- Max. operating pressure: 15 bar
- Switch-on pressure range: 0–10 bar
- Switch-on pressure (factory setting): 1.5 bar
- Tank capacity: 1 L
- Max. ambient temperature: 40 °C
- Max. liquid temperature: 80 °C
- Protection rating: IP65
- Operating position: vertical
IPRO - 36-month (3-year) manufacturer's warranty. Warranty and post-warranty service is provided by Dambat.
Dambat - a trusted manufacturer of pumps and hydrotechnical equipment with quality certifications.
Frequently asked questions (FAQ) - WATER-PASS 2 controller
What is the WATER-PASS 2 controller for?
The WATER-PASS 2 is an electronic pump controller from IPRO that automatically switches the pump on when water is drawn and switches it off when water use stops. It maintains constant pressure in the installation and protects the pump from running dry.
What is the 1 L tank in the WATER-PASS 2 for?
The 1 L tank reduces water hammer when the pump switches on and off. For this reason, an additional diaphragm tank is not installed with the WATER-PASS 2.
Does the WATER-PASS 2 protect the pump from running dry?
Yes. When there is no water, the controller switches off the pump after 8 seconds, protecting it from running dry. To restart it, disconnect and reconnect the power supply.
What kind of water can the WATER-PASS 2 work with?
The controller is designed to work with clean water that contains no mechanical impurities. Sand or iron particles may damage the device.
What is the factory-set switch-on pressure of the WATER-PASS 2?
The switch-on pressure on the WATER-PASS 2 is factory-set to 1.5 bar. The switch-on pressure can be adjusted from 0 to 10 bar, allowing you to tailor its operation to your installation.
How is the WATER-PASS 2 different from the WATER-PASS?
The WATER-PASS 2 has a 1 L tank that reduces water hammer, so it does not require an additional diaphragm tank. It also comes with a factory-set switch-on pressure of 1.5 bar. The other parameters and operating principle are the same as those of the WATER-PASS model.
Where can I buy the WATER-PASS 2 controller?
The manufacturer does not sell directly to customers. The WATER-PASS 2 controller is available from retail partners, plumbing wholesalers, and authorized online distributors.
What warranty does the WATER-PASS 2 come with?
The IPRO WATER-PASS 2 controller comes with a 36-month (3-year) manufacturer's warranty. Warranty and post-warranty service is provided by Dambat.

