IBO KBFU 100-5.5 pump Sludge Submersible 400V
KBFU 100-5.5 is a three-phase pump Sludge with a power of 5.5 kW, powered by 400 V with a DN 4" connection, achieving a capacity of 2200 l/min. The model is intended for intensive drainage works with thick sludge - where the pump alone without a bottom mixer is not able to effectively suck sedimenting sludge.
For whom
-
Construction companies working with bentonite and drilling material – efficiency of 2200 l/min with a powerful 5.5 kW engine shortens the dewatering time of deep excavations with thick sludge.
-
Industrial plants with settling tanks and separators – the combination of an agitator and high efficiency works well when emptying sedimentation tanks and settling ponds.
-
Tunnel and geotechnical contractors – the agitator and powerful engine cope with drilling material when constructing piles and diaphragm walls.
-
Engineers designing sludge pumping stations – big Connection DN 4" and high efficiency simplify the hydraulic design of installations with a four-inch pipeline.
Application
The KBFU 100-5.5 model is intended for pumping media containing sediments and solid impurities found in construction excavations, retention reservoirs and when draining flooded areas. The design of the pump allows it to operate in difficult conditions in which standard clean water pumps would not work due to the presence of suspensions and small impurities.
A key element of the design is the cooling jacket surrounding the engine. Thanks to it, the pump does not have to be fully immersed in the pumped medium to maintain a safe operating temperature - the engine is cooled by the jacket wall even when the liquid level in the tank is very low. Thermal protection built into the motor winding provides an additional layer of protection against overheating during long-term continuous operation.
Features of the KBFU 100-5.5 pump
- Adaptation for pumping water with sand: YES
- Cooling Jacket: YES
- Discharge port: 4" threaded, vertical direction
- Thermal protection: YES (built into the motor winding)
- Agitator: YES (chrome alloy)
- Float switch: NO
- Bearings: NSK (Japan)
- Working mode: continuous
IBO – 24 months (2 years) manufacturer's warranty.
Dambat – a trusted manufacturer of pumps and hydrotechnical equipment with quality certificates.
Frequently asked questions (FAQ) – pump Sludge KBFU 100-5.5
What is the difference between KBFU 100-5.5 and KBFU 100-3.7 T?
The 100-5.5 model has higher power (5.5 vs 3.7 kW), higher efficiency (2200 vs 1650 l/min), higher lift (23 vs 18.5 m) and - the key difference - is equipped with an agitator. This is the choice for heavier applications with thick sludge, where the 3.7 T model without a mixer may be insufficient.
What is the agitator used for in the KBFU 100-5.5 pump?
The agitator is a bottom mixer mounted under the pump impeller. It sets the sludge into swirling motion, breaking up aggregates and liquefying suspensions at the inlet. Without an agitator, thick sediments would sediment at the bottom of the tank, making it much difficult or impossible for them to be sucked in by the impeller.
Can KBFU 100-5.5 be used in settling ponds?
Yes - the combination of an agitator and a capacity of 2200 l/min works well when emptying sludge tanks. Make sure that the chemical composition of the medium is within the permissible parameters for cast iron and stainless steel - in case of doubt, we recommend contacting the Dambat technical department.
Where to buy the IBO KBFU 100-5.5 pump?
The model is available from Dambat trading partners, installation wholesalers and technical stores. Dambat does not sell directly.
How long is the warranty for KBFU 100-5.5?
IBO – 24 months (2 years) manufacturer's warranty. Warranty and post-warranty service is provided by Dambat, Adamów 50, Grodzisk Mazowiecki.
