Deep pumps are devices for special tasks that can work several or even a dozen or so meters underground. They are irreplaceable in many situations: they buy water households and make it available at the appropriate pressure at all consumption points; help in drawing water necessary to water the vegetation; And larger constructions are perfect for a large scale in industry. However, for the deep pump to fulfill its task well, it is necessary to install it. What is he about? How does it connect to the parameters of the device? And what should you remember? We answer these and other questions in our article.
Parameters and device assembly
In order for the assembly of the deep pump to run as planned, it is necessary to carefully select the device. What is worth paying special attention to? First of all, on the quality of workmanship and somehow used in the entire process of materials. It turns out that the use of modern technologies in the engine and hydraulic elements and the presence of appropriate protection positively affects not only the pump operation, but also the process of its mounting. When making a choice, we also need to pay attention to the efficiency and lifting height, as well as whether the pump can work in the so -called dirty water. It is also extremely important to check what soil and water conditions are in our area. What does this mean? It is necessary to determine at what depth the aquifer is located and whether there are large fluctuations in its level. The size of the device is also a key element - it should be smaller than the diameter of the well.
What to remember?
In most cases, deep -sea pumps are mounted in a vertical position. The exception are those devices whose construction allows installation at an angle, but not more than ninety degrees from the vertical. Importantly, if the assembly takes place in a well made of concrete vertebrae or in the tank, it is necessary to enclose the device into a cover pipe.
Deep pump It cannot be abandoned to the bottom of the well. The optimal place is usually determined by the manufacturer himself, giving the minimum height difference between the pump engine and the bottom of the well, the minimum water mirror level above the pump hydraulics system, as well as the maximum pump depth below the water mirror level.
It is also worth remembering that the assembly of the deep pump is a complicated and responsible task that requires knowledge and experience. To enjoy the correct operation of the device, you should use the help of specialists in this regard.
Deep pump - how to mount?
To assembly deep pump It was possible, it is necessary to gather all the elements included in the so -called pump kit. The most important is, among others Hydrophore tank, deep pump, three -way output, pressure switch, pressure gauge, check valve, connector, as well as the head to close the well.
We start the work by connecting the right elements, i.e. applying the pump along with a check valve, connector and head directly to the deep engine. So we must:
- screw a check valve and fitting into the pump,
- connect the power pipe to the deep pump,
- twist the head,
- place an electric cable in a hole intended for it, located in the head,
- Connect the water supply pipe.
After completing these stages, we can put the pump in the well. Another important steps are:
- ligation at the head of the cable from the deep pump,
- closing the well with a head,
- connecting the pipe pressing water to the hydrophore reservoir,
- Installation of accessories, including a pressure gauge, pressure switch and three -way output.
After completing all stages, it's time to mount the tank on the wall, connect the PE pipe to a five -way output installed on the tank and connect the electrical cable to the pressure switch.
Of course, each situation requires analysis and flexibility. For example, although in most cases the pump should be installed so that the lowest, dynamic level of the water mirror is a minimum of two meters above the pump's pressure bush, not every system allows it. If we meet with such a problem, special security should be installed that prevent dry pump operation. In addition, when leaving the pump, make sure that the power cable is attached to the pipe with plastic bands so that it does not break and destroy. In turn, directly above the pump should be installed a check valve protecting the device against the strokes of returning water.
Adequate security
Before starting a permanent use of the pump, it is important to remember several necessary security. First of all, it is worth checking what the well's performance is. How to do it? It may be helpful to pump water without a break for at least an hour. If the water we extract is to be consumed by people, it is necessary to examine its fitness and composition. Safety is also determined by the sealing of all elements that prevents the mixing of drinking water with ground water.
In order for the entire installation to work without interference, it is necessary to properly arrange the electrical cable, which should be secured with plastic stress reducing. It is also necessary to take into account the seasonally low and even minus temperatures that can cause smaller and greater damage. To prevent them, it is worth using the thermal and insulation layer and remember the appropriate depth of the most important elements. Importantly, the pipes we use should be connected by flexible wires that reduce vibrations and protect them from dangerous unsealing.
Our offer
If you are looking for high quality products, select deep pumps IBO Italy, which are a phenomenon on the Polish and world market. The design of the devices allows them to be used in various irrigation systems - both in households and on an industrial scale. Most IBO pumps have increased sand resistance, which means that they can work efficiently even in difficult conditions.
The solutions available on our website are proposals used in water supply installations, irrigation systems, as well as in fire protection installations. The deep pumps we create are the highest quality equipment, made of excellent quality materials. The devices are characterized by a wide range of parameters, as well as professional engine performance. Check our offer today!
